USATransdoctor.com
These recommendations do not cover all possibilities. They are some things to check before you have your transmission rebuilt. Always check transmission fluid level first. Always run a scanner on any computer controlled transmission. On modulated transmissions make sure they have enough vacuum.


GMC VEHICLES
FIND THE MAKE OF YOUR VEHICLE
CLICK ON THE YEAR OF YOUR VEHICLE

Caballero 1978-87 T350 1985-87 4spd700R4      
Jimmy 1970-82 T350/C 1982-93  700R4 1993-05 4L60E    
S 15 / Sonoma 1983-91 700R4 1992-05 4L60E      
Safari Van 1985-93 700R4 1993-06 4L60E      
Suburban 1987-90 T400 3spd 1987-92 700R4 O/D 1991-06 3/4 ton O/D 4L80E
 17 pan bolts
1993-06 1/2 ton 4L60E O/D
 16 pan bolts
 
Truck  C/K Series 1966-90 T400 1969-86 T350/C 1982-92  700R4 !993-06 4L60E 1991-08 3/4 ton 4L80E 17 bolt pan
Vans 1969-86 T350/C 1975-90 T400 1983-92 700R4 1993-06 4L60E 
 
16 bolt pan
1991-07 4L80E
 17 bolt pan
Yukon 1991-93 700R4 1993-06 4L60E16 bolt pan or 4L80E 17 bolt pan      


                      

 

 

          

4L60E / 4L80E  
The transmissions above, are rear wheel drive 4speed automatics that are all computer controlled. Common problems are: Check engine light comes on. The transmission shifts erratically, slips or does not shift at all.

These problems can be caused when the external sensors on the vehicle go bad. The input and output speed sensors, throttle position sensor or vehicle speed sensors need to be checked. Always run a scanner first to see if a sensor is causing your problem.  
The 4L60E transmission also has a problem with a hard 1-2 shift when hot, and a 1870 code. When rebuilding the transmission, I recommend that you always replace the valve body plate and install a sonnex Valve Kit TCC Regulator W/Sleeve. This is to help against having these problems in the future. On the 4L60E make sure you always us a AC Delco hardened shell when rebuilding the transmission.

The 4L80E transmission has a lot of problems with the input and output speed sensors on the side of the transmission. They should always be checked first if you are having a shifting problem.

 An ignition switch that goes bad can cause a false shift solenoid code that comes up on a scanner. So be careful.


Back To Home Page         Back To Top of Page

 

 

 

 

 

 

 

 

4T40E / 4T60E / 4T80E
The transmissions above are 4 speed automatics that are computer controlled.  The most common problems are: Your check engine light comes on. The transmission starts shifting erratically or not at all. 

Make sure you or a shop runs a scanner on the vehicle.  You want to see if a sensor has gone bad causing your problem.  Always check your modulator line on the 4T60E transmission to see if there is fluid inside. If fluid is inside the line, then the modulator is no good.

 

Back To Home Page         Back To Top of Page

 

 

 

 

 

 

 

 

125c
This transmission is a front wheel drive, 3 speed automatic.  Common problems are: The transmission shifts soft and early. It shifts hard and late.  The engine stalls as you come to a stop when the engine is hot.

Always check the throttle pressure cable that goes from your transmission to your carburetor or throttle body depending on the configuration of your engine. This controls the shift points and sometimes the heat causes the little plastic connector that holds it on to become brittle and break, causing erratic shifting.

Now to fix the engine stalling problem. Check your lock-up solenoid in the transmission side pan. The majority of the time it sticks when the transmission becomes hot.

 

Back To Home Page         Back To Top of Page

 

 

 

 

 

 

 

 

2004R / 700R4
The transmissions above are rear wheel drive, 4 speed automatics. The shift timing is controlled by a throttle pressure cable that connects from the transmission to the carburetor or throttle body depending on the configuration of your engine. Always check these items first before you purchase a transmission.

Also, make sure your clutch fan on the front of the motor is not starting to seize up. This causes the engine to sound unusually loud, almost like the transmission is not shifting into 4th gear.

Also, If your engine stalls when you come to a stop, check the lockup torque converter clutch solenoid. They often stick when hot.  On the 700R4 make sure you always us a AC Delco hardened shell when rebuilding the transmission.

 

Back To Home Page         Back To Top of Page

 

 

 

 

 

 

 

 

 

200C
This transmission is a rear wheel drive, 3 speed automatic.  Common problems are: The transmission shifts early and soft. It shifts late and hard. It does not shift at all.

Always check the throttle pressure cable that goes from your transmission to your carburetor or throttle body depending on the configuration of your engine. This controls the shift points and sometimes the heat causes the little plastic connector that holds it on to become brittle and break, causing erratic shifting. This style transmission also has a problem with the reverse clutches burning up at about 80,000-120,000 miles. make sure you replace the little seal in the case.

 

Back To Home Page         Back To Top of Page

 

 

 

 

 

 

 

 

T350 / T400
The transmissions above are rear wheel drive, 3 speed automatics.  Common problems are: The transmission shifts erratically. Loosing transmission fluid without a trace of a leak.

The Turbo 400 has a modulator on the passenger's side of the transmission pointing towards the passenger's door. The Turbo 350 has a modulator on the rear of the transmission.  Pull the rubber line off the modulator and see if transmission fluid comes out of the line.  If fluid comes out, the modulator is no good and can cause the above problems.

You should check your fan clutch from time to time. I see a lot of them seize up confusing people into thinking they need a transmission. So be careful.

When you pull the shifter from 3rd to 2nd, you should be able to feel what you would call engine braking. Now if you don 't, and if you are driving a vehicle with a T400 transmission, there is an accumulator piston, which is made of plastic, that often breaks. If you have your transmission rebuilt, always make sure they put an aluminum accumulator piston in. They don't break.

 

Back To Home Page         Back To Top of Page

 

 

 

 

 

 

 

 

3T40E     This transmission is a 3 speed front wheel drive automatic that is all computer controlled.  If your transmission starts shifting erratic or not at all, make sure that you or a shop run a scanner on the vehicle. You want to see if you have a sensor that has gone bad, causing your problems.

 

 

Back To Home Page         Back To Top of Page

 

 

 

 

 

 

 

 

440T4 / 325 4L
The transmissions above are front wheel drive, 4 speed automatics. Shift timing is controlled by a throttle pressure cable that connects from the transmission to the carburetor or throttle body, depending on the configuration of your engine. Check this cable first. Make sure the cable is not out of adjustment.

The 440T4 also has a modulator that controls shift firmness. If this modulator goes bad it can shorten the life to your transmission. Pull the vacuum line off at the transmission, if there is fluid in the line, the modulator is no good.

If you have a 440T4 transmission, and your engine stalls when you come to a stop, make sure you check the lockup torque converter clutch solenoid, they often stick when hot. 

If your vehicle is equipped with a 440T4 transmission, the engine must be in good engine tune. If the engine is running rough or needs tuned up, it can shorten the life of your transmission.

 

Back To Home Page           Back To Top of Page